“Emak Group Middle East" LLC - MFT1815 Megger Multifunction Tester - Megger Казахстан

Home
Electrical measuring instruments
MFT1815 Megger Multifunction Tester

Article number: ENRGSKN-149

MFT1815 Megger Multifunction Tester - Megger

Designed for measuring and testing all parameters of low-voltage networks and electrical installations (wiring, RCD, grounding, etc.) with voltage up to 1 kV. Certificate of initial verification -1600 rubles

Electrical safety parameter meter MFT 1815 , manufactured by M egger (England), is designed for measuring and testing parameters of electrical installations (wiring, RCD, grounding, etc.) with voltages up to 1000 V.

MFT 1815 allows you to test insulation voltages of 250V and 500V with resistance measurements in the range from 10kOhm to 500MOhm. The integrity of the circuit is determined at a current of 200 mA.

Also, the multifunctional tester MFT 1815 carries out testing of RCDs with a nominal value of 30 mA, 100 mA, 300 mA, 500 mA. Testing is carried out with current: 1xI in position 0? and 180.

Measuring parameters of the MFT 1815 M egger loop conducts two-wire method. 2-wire testing of electrical circuits is performed using only two test leads, measurements - Phase - Ground / Phase - Zero / Phase - Phase. A third wire, which could cause confusion in identifying the part of the circuit under test, is not needed. Measurements take place in the voltage range from 28V to 280V AC in single-phase circuits to 480V in three-phase circuits. Short circuit current (SC) is calculated up to 20kA using the measured voltage and loop resistance.

The multifunction tester MFT 1815 measures alternating voltage up to 600V, allows you to measure frequency in the range from 15Hz to 400Hz and determine the phase sequence.

The multifunctional tester MFT-1815 has a large LCD display with digital display and imitation of an analog scale. Selecting test or measurement mode is simple and convenient, and is also separated by color gradation. Much attention is paid to testing safety; if the electrical installation being tested is energized, the operator will be notified about this, and the device will not fail (within the CATIV standard).

The multifunctional tester MFT1815 M egger is made in a shock-resistant, moisture-dust-proof housing (IP 54).

Functional features of the MFT 1815 device:

Measuring network voltage and frequency
250V and 500V insulation testing
Measuring loop resistance and calculating short-circuit current
Testing of RCDs rated 30 mA, 100 mA, 300 mA, 500 mA.
RCD current testing: 1xI in position 0? and 180

MFT1815 Megger Specifications :

Insulation testing
Insulation Test Voltage	500 V, 250 V
Short circuit/load current	1.5 mA/1 mA
Resistance measurement and conductivity test
Resistance measurement ranges	0.01 Ohm – 99.9 Ohm; 100 Ohm – 99.9 kOhm
Max. Voltage	5V±1V
Current	205 mA ± 5 mA
Loop testing
Testing	Phase-Phase, Phase-Neutral(Zero), Phase-Ground
Phase-Ground Voltage	48 V – 280 V (45 Hz-65 Hz)
Voltage Phase-Phase	48 V – 500 V (45 Hz-65 Hz)
Loop resistance measurement range	0.01 Ohm – 999 Ohm
Short circuit current	Up to 20 kA
RCD test
RCD type	A, AC
Currents	30 mA, 100 mA, 300 mA, 500 mA
Mode	Rated current testing
Measuring Network Parameters
Measuring network voltage and frequency	10V – 600V (15Hz-400Hz)
Common parameters
Operating temperature range	-10 °С…+55 °С
Work from:	6 AA batteries
Weight	1 kg (with batteries)
dimensions	150 mm x 85 mm x 235 mm
Protection from dust and moisture	IP 54
Safety	CAT IV